Activate Carbon Tower

Category image Category image

Efficient Compressed Air Purification with Activated Carbon Tower

An activated carbon tower is used to purify compressed air by removing oil aerosols, odors, and volatile organic compounds (VOCs). It ensures clean and dry compressed air, essential for the food, pharmaceutical, and electronics industries.

When the carbon is saturated, it can be replaced or regenerated to maintain effective filtration. Carbon towers provide a reliable and eco-friendly solution for compressed air systems.

Filter
Set Descending Direction

23 Items

per page
View as Grid List
Filter
Set Descending Direction

23 Items

per page
View as Grid List

Activated carbon towers for oil vapour removal

Activated carbon towers are used where compressed air must contain extremely low levels of oil vapour, hydrocarbons and odours. The compressed air passes through a bed of activated carbon, where gaseous hydrocarbons and oil vapours are adsorbed onto the large internal surface area of the carbon.

Unlike a conventional coalescing filter, which primarily removes particles and liquid aerosols, an activated carbon tower targets contaminants that remain in vapour form. This makes it an important final purification stage in applications requiring very high compressed-air quality.

C-ACT compact activated carbon towers

The C-ACT series is designed for smaller compressed-air flows and uses threaded connections. With capacities from approximately 8.4 to 162 m³/h, the range provides a compact solution for smaller installations requiring efficient oil vapour adsorption.

ACT industrial activated carbon towers

The ACT series is intended for larger industrial compressed-air systems. These units use DIN flange connections and cover substantially higher flow rates, from approximately 190 to 4,200 m³/h.

How does an activated carbon tower work?

Activated carbon contains an extremely large internal surface area. As compressed air passes through the carbon bed, oil vapours, hydrocarbons and many odour-producing substances are attracted to and retained on the carbon surface through adsorption.

Under the specified operating conditions, the C-ACT and ACT series can reduce residual oil content to as low as approximately 0.003 mg/m³. The actual service life of the activated carbon depends on operating conditions, inlet contamination, air flow and the effectiveness of upstream filtration.

C-ACT or ACT?

Series Typical flow range Connection Typical application
C-ACT Approx. 8.4 to 162 m³/h Threaded Smaller compressed-air installations and lower flow requirements
ACT Approx. 190 to 4,200 m³/h DIN flange Larger industrial compressed-air systems and higher flow requirements

The basic adsorption principle is the same for both ranges. The primary difference is capacity and connection type. C-ACT covers compact systems with lower flow requirements, while ACT extends the same oil-vapour removal principle to considerably larger industrial installations.

Pre-filtration is essential

Activated carbon is intended primarily for adsorption of vapours. Liquid water, oil aerosols and particles should therefore be removed before the compressed air reaches the carbon bed. Effective upstream filtration helps protect the activated carbon, maintain adsorption performance and extend its useful service life.

A fine downstream filter can also be used to retain any small carbon particles that may be released from the adsorption material. For larger ACT systems, suitable upstream and downstream filtration should therefore be considered as part of the complete treatment system.

Important when selecting an activated carbon tower: Selection should be based on compressed-air flow, operating pressure, inlet temperature and the required air quality. The quality of the air entering the tower is particularly important, because excessive liquid oil or water can significantly reduce the effective life of the activated carbon.

Activated carbon tower and adsorption dryer

An activated carbon tower and an adsorption dryer perform different tasks. The adsorption dryer removes water vapour and reduces the pressure dew point, while the activated carbon tower removes oil vapours, hydrocarbons and odours.

Where very dry and very clean compressed air is required, the two technologies can therefore be combined. The activated carbon tower may also be used as a stand-alone purification stage where oil vapour removal is required but additional drying is not necessary.

Typical applications

Activated carbon towers are suitable for compressed-air systems where oil vapour or odour can affect the process, product or downstream equipment. Typical applications include food and beverage production, electronics, pharmaceutical and chemical processing, painting and coating processes, instrumentation and other installations requiring high-purity compressed air.

Frequently asked questions

What does an activated carbon tower remove?

It is primarily used to adsorb oil vapours, hydrocarbons and odour-producing substances from compressed air. Particles, liquid water and oil aerosols should normally be removed by suitable upstream filters.

What is the difference between C-ACT and ACT?

Both use the same activated carbon adsorption principle. C-ACT is the compact range with threaded connections for lower air flows, while ACT uses flanged connections and covers much larger industrial flow rates.

How low can the residual oil content be?

Under specified operating conditions, the activated carbon adsorbers can reduce residual oil content to approximately 0.003 mg/m³.

Does an activated carbon tower replace a compressed-air dryer?

No. An activated carbon tower primarily removes oil vapours and hydrocarbons, while a compressed-air dryer removes water vapour. The two systems can be used together when both low moisture and very low oil content are required.

Why is a pre-filter required before activated carbon?

Activated carbon performs best when liquid water, oil aerosols and particles have already been removed. Effective pre-filtration protects the carbon bed and helps maintain adsorption capacity and service life.